Install this checklist on your phone: Tap your browser menu and choose "Add to Home Screen". It will work offline.
How to use: Complete Before sections, then run the machine 15–20 min and observe During items, then shut down and finish After. Any Fail blocks dispatch to paint shop.
Before1. Pre-Run Inspection
0/3
All fasteners (bolts, nuts, lock-nuts) torqued to spec — no loose joints
सभी फास्टनर्स (बोल्ट, नट, लॉक-नट) को निर्धारित टॉर्क पर कसा गया है — कोई भी जोड़ ढीला नहीं है।
Welds visually clean — no cracks, undercut, or unfused beads
वेल्ड देखने में साफ़ हैं — कोई दरार, अंडरकट या बिना जुड़े बीड्स नहीं हैं।
All safety guards installed (belt, flywheel, PTO shaft)
सभी सुरक्षा गार्ड लगाए गए हैं (बेल्ट, फ्लाईव्हील, PTO शाफ़्ट)
Before2. Pulley & V-Belt Alignment
0/3
Drive and driven pulleys parallel (laser tool or straight-edge)
ड्राइव और ड्रिवेन पुली समानांतर हैं
All V-belts seated fully in pulley grooves (not riding high)
सभी V-बेल्ट पुली के खांचों में पूरी तरह से बैठे हों (ऊपर की ओर न हों)।
Belt tension correct (~15 mm deflection at midpoint)
बेल्ट का तनाव सही है (~मध्य बिंदु पर लगभग 15 mm का झुकाव)
Before3. Bearings & Shafts (Pre-Run)
0/3
Shaker pitman shaft moves through full stroke freely
चलना शाफ़्ट पूरे स्ट्रोक में स्वतंत्र रूप से चलता है।
No detectable axial or radial play in any bearing housing
किसी भी बेयरिंग हाउसिंग में कोई भी पता लगाने योग्य प्ले नहीं है।
Flywheel locked on shaft — no wobble
फ्लाईव्हील शाफ़्ट पर लॉक किया गया है — कोई डगमगाहट नहीं।
During4. Vibration (During Run)
0/2
Whole machine vibration acceptable
पूरी मशीन का कंपन स्वीकार्य है।
Hand-feel on bearing housings: low/uniform vibration only
बेयरिंग हाउसिंग पर हाथ से महसूस करना: केवल कम/एकसमान कंपन।
During5. Noise & Sound (During Run)
0/3
No metal-on-metal knocking sound
धातु से धातु टकराने की कोई आवाज़ नहीं
No rattling from loose panels, covers, or fasteners
ढीले पैनलों, कवरों या फास्टनरों से कोई खड़खड़ाहट नहीं।
No grinding sound from bearings
बेयरिंग से कोई घिसने की आवाज़ नहीं आ रही है।
During6. V-Belt Performance
0/4
No belt slippage (mark belt+pulley with chalk, watch one rotation)
बेल्ट नहीं फिसलेगी (बेल्ट और पुली पर चॉक से निशान लगाएँ, एक चक्कर देखें)
No belt walking / hopping in groove
ग्रूव में बेल्ट चलना/कूदना नहीं चाहिए।
No belt flap or whipping (Belt Palatna)
बेल्ट का बेल्ट पलटना
Belts not running excessively hot to touch after stop
रुकने के बाद बेल्ट छूने पर बहुत ज़्यादा गर्म नहीं हो रहे हैं।
During7. Bearing Performance
0/2
All bearing housings warm only, NOT hot (≤60 °C / hand-bearable)
सभी बेयरिंग हाउसिंग केवल गर्म हैं, गर्म नहीं (≤60 °C / हाथ से छूने लायक)
Shafts run true — no visible runout at exposed shaft ends
शाफ़्ट बिल्कुल सीधे चलते हैं — शाफ़्ट के खुले सिरों पर कोई भी स्पष्ट विचलन दिखाई नहीं देता।
During8. Mechanism Function
0/2
Shaker stroke length within range
चलना स्ट्रोक की लंबाई सीमा में है।
Sieves oscillate freely without binding against frame
छन्नियाँ फ्रेम से टकराए बिना स्वतंत्र रूप से हिलती हैं।
After12. Pre-Paint Sign-Off
0/2
All non-conformances recorded with corrective action
सभी दर्ज विसंगतियों के साथ सुधारात्मक कार्रवाई
Any failed item rectified and re-tested
कोई भी खराब आइटम ठीक करके दोबारा टेस्ट किया गया।
Last sent 22 min ago · REJECT · S/N BI/7500/2451/2026/002